Thursday, February 26, 2009

Quick Change Runners - Part 2

After the horrifying job that put 4 strong adults to work, while putting the QCR system and runner plastic on our wooden training toboggan sleds (read the entry here), what could be more horrifying, you think?

Well, besides the thought of having to ever change the plastic in the future, not being able to properly pull it over the aluminium rails, there is one, slightly more disasterous thing, that can happen... Yes, you guessed it right - after a few training runs several screws at the end of the runners broke and the rails bended out of the runners! Now, that is a horror.

It took us a couple phone calls to consult with couple fellow mushers, way more experienced with this system than us, the QCR rookies, and some strong nerves and patience and also convincing of ourselves, that we just have to drill into the runners again and nothing will go wrong this time. Well, we´ll see about that today, as I intend to try it out in action with a 12 dog team.

So yesterday we finished the work on my sled and if it turns out ok (please, send positive thoughts and vibes!), we´ll do it the same way with Jachym´s.
PHASE 1: Peeling off the QCR runner plastic
Peeling off the runner plastic. Way easier than putting it on (the first time at least). It´s like peeling a banana :)

First step over - that was easy done. See the edge of the runner plastic sticking out of the runner on the right side? That´s where the screws broke off.

Peeling off the last pice on the second runner. The aluminum rail sticking out where the screws broke, is well visible on this picture as well (on the further runner).

PHASE 2: Removing the alu rails from the runners

PHASE 3: (my personal favourite)
Rescrewing the alu rails onto the runners - the SMART way
Now, why did we want to go through the trouble of putting these metal underlays under each hole? This is the big inovation - to elevate the rail and create space between the rail and the runner. This way the QCR runner plastic should be smooth and easy to slide onto the rail. We´ll see about that in phase 4....

Make sure the screws you are using are stainless-steal. The only problem you may run into is that the screw heads have a 3mm square shape profile, which is not a standard one in Europe, so you probably won´t find a corresponding bit in your workshop. But after a bit of running around town, we found them in hardware store called Gardin & Persson.

And here it comes (drumrolls please):
PHASE NR.4 - Pulling runner plastic over the rails

This one´s for you, Richard! :) Do you see how I, singlehandedly pulled the plastic over the rail? And how I (alone) have used just my thumbs to push the last few centimeters on?

YES! It was that easy! We could do this for living! :) LOL

Thank you Rikke for the suggestion of using the underlayes. Now we´ll just have to see how it all works in reality!

And the moral of the story? Fellow musher and friend Karsten told me, when I mentioned I felt like an idiot and should have asked someone else to mount the QCR system on our sleds: "If you didn´t have to go through this, you would have missed the learning process. And you can´t graduate from rookies to masters. Next time you can give advise on this to someone else." -- But that will take a few more runners to work on, I guess! :)

So may our experience and this log help other QCR rookies in their struggle!

Happy Trails,
Katerina

4 comments:

Anonymous said...

LOL!! There is a hard way and a easy way to do all things I suppose, but the possitive thing is that my triceps got a nice work-out the first time! :)

Anonymous said...

the above note is from me , Richard, for those who didn´t know :)

Rikke said...

Good it went easier this time-
Per Olav got boxes of those bits that goes with the screws and allways sent one to those ordering rails...
BUT I see a little mistake you have done- the last screw shoud sit as close to the end of the ski as possible, and then cut of the end of rail. When its some cmtrs behind the rail and end of ski this can bend....

Rikke said...

one more thing...
when changing plastic have a flat screwdriver in hand to drag along under the rail to remove ice and snow before putting new plastic on. With the *skiver* under the rail it also get more space for ice...

Related Posts Plugin for WordPress, Blogger...